Posts Tagged "Painting"

Decorative Painting 101 – Wall Stencils Technique

Posted by on Feb 19, 2017 in Uncategorized

The wall stencils that heroically got into the market have over time dominated smart and lovely wall decor. They exist in many designs, and it is one’s personal choice to pick whatever plan suits them. The good thing is with just a little practice; even a DIY novice can do the job.

Decorative Painting 101_Wall Stencils TechniqueThe article provides a guideline for using the wall stencils to make an attractive design on the walls. The tools needed include

  • Stencil
  • Stencil brush
  • Paint tape
  • Paper towel
  • Painting container
  • Pencil
  • Spray adhesive
  • Leveler

The manual

A clean, fresh wall with white coats of paint is the starting point. There are two approaches involved, and one is putting the stencil in the middle whereas another is putting it at the corner. Central placement, however, is advisable for symmetry purposes. Application of the spray adhesive on the wall then follows. It ensures right stationing of the stencil. After confirming the location of the stencil, it is adjusted on the wall. The alignment should be beautiful to avoid any flows that may occur.

After proper alignment, use a pencil to mark the stencil alignment on the wall. The direct use of the stencil is not as prudent as employing the utilization of a painters tape. This because the tape does not make the wall dirty and as such no cleaning after that as in the use of pencils of which the pencil marks will need erasing after stencil painting.

After the tape or pencil, painting the stencil begins. The paper towel is then used to shed most paint into it. Next, fill the stencil with paint using the stencil brush. For best results, punching motion is the technique. Because of the extra paint on the towel, fill the brush three to four times for the different areas.

When taking away the Stencil, the adhesive side should always face up. The purpose is the removal of paint that may have stuck beneath the stencil. Clean the wall from side to side using the tip of a brush or using the paper towel. For you to paint corners, a stencil is best for securing a particular side, done by holding one side down using the painters tape.

Some other notable facts include:

For best results, quality stencil brush is a necessity. Stenciling should not directly begin from the wall but instead tried on a large board first, thus reduces the chances of ruining the wall and guarantees a uniform and clean look. It takes the time to do the stenciling job and hence a lot of patience is necessary.

Employing the use of a foam roller to stencil is the fastest easiest and quickest form of stenciling. However, this calls for a decision to have the entire wall stenciled. It may also call for a small section of the wall to stencil.

Using a roller foam

The paint can is properly shaken followed by spraying of the stencil using the spray adhesive. The stencil is then carry put on the wall to start the work. Additionally, to avoid blotting, do not fill the roller with paint. Pressure is needed in the roller use for crisp and neat outcomes. Roll the roller over the stencil carefully.

If you do this right, look out for the results. Should it not turn out as expected, repeatedly move the roller on the stencil using light strokes, the process continues until the results turn out as expected. Analyze the effects simply by lifting the stencil off the corner. It should start at the initial stages of the job based on the ease of making changes at the beginning after which the stencil is put back to continue the job.

In the rolling process, if the roller runs short of paint, refill it with paint and, do not press hard on the stencil to eliminate the excess paint.

When closer to the edge, rolling over the edge is necessary. The paint is then cleaned using baby wipes. Tape can be added to the edges of the stencil to avoid paint reaching on those parts.

Stencil repeatedly until you achieve the desired. An advantage is regular cleaning is inappropriate. Clean the stencil every time you want to apply different color stains.

Learn More

Decorative Painting 101 – Cracked Wall Effect

Posted by on Jan 15, 2017 in Uncategorized

Use faux painting techniques to create different decorative effects for your walls. The main idea behind a cracked wall effect comes from the common use of antiques or distressing techniques that would give objects an aging appearance. For you to accomplish this result, you need to apply a crackling medium in between paint layers.

Decorative Painting 101_Cracked Wall EffectWith a crackling medium in place, the top layer above it would crack in random patterns. Therefore, one can easily see the base coat, which is most definitely of a different color from the top layer. The size and depth of your cracks would depend on how thick is your crackling medium. These results are also affected by the manner in which you apply the top paint. Practice makes perfect, so by constant practice, you are likely to achieve special effects.

Step 1: Prepare the space by ensuring the wall is clean and dry. If required, use primer and apply a color that is darker than the base coat color. Cover those areas that need protection from the paint with painter’s tape. Additionally, cover floors with plastic sheeting.

Step 2: Use a roller for the application of the base coat color. Try rolling the paint in one pattern as much as possible and cut in edges using the paintbrush where necessary. Allow the base coat time to dry overnight.

Step 3: Apply the crackling medium consistently using a short nap roller cover or nylon paintbrush. For more visible and pronounced cracks, apply a thicker coat. Even so, do not overwork the crackling medium or overlap brush strokes. Apply on smaller sections at a time until you cover the entire area. Get rid of all painter’s tape before the crackling medium becomes dry. Give the medium time to dry as stipulated on the manufacturer’s manual.

Step 4: Regularly reapply painter’s tape. Stain the topcoat paint evenly as soon as the crackling medium dries. Utilize the paint roller for cracks more delicate and a paintbrush for cracks more intense. Get rid of the painter’s tape after an hour of drying time, and then allow topcoat to dry overnight.

You’ll need:

  • Paint roller
  • Painter’s tape
  • Paint tray
  • Plastic sheeting
  • Crackling Medium
  • Roller covers
  • Base coat latex paint
  • Nylon paintbrush
  • Top coat latex paint

Tips

Before you begin any procedures, familiarize yourself with the crackling medium on a practice board, and experiment the different medium applications even before you advance to work on your wall.

Confirm the manufacturer’s instructions concerning the type of paint to use with a particular crackling medium. Many would suggest satin or a flat sheen.

Warnings

Ensure you remove the painter’s tape before the crackling medium dries, otherwise, can pull off part of the glaze and damage your finish.

Apply the outermost coat immediately after the crackling medium dries, as waiting too long can destroy the effect.

Conclusion

Remember that nothing comes on a silver platter. Therefore, you have to practice consistently on your painting and decorative skills before you become an expert.

Learn More

Concrete Painting Tips and Tricks

Posted by on Dec 5, 2016 in Uncategorized

Painting concrete surfaces is not about just splashing colors on the wall, but it requires skills, tools, and temperament. The cement painting is tricky because concrete breathes, carries moisture, and sucks up the paint. You can paint drywall in a day, but painting concrete takes about a week to finish.

concrete painting tipsHere is a set of tips and tricks to help you in paint concrete like a pro:

Cleanse the Concrete

Concrete is a porous surface that is why it traps grease, dirt, and oil. Thus, cleaning concrete is a vital step. First of all, use trisodium phosphate to remove oil and dirt. You can opt for an eco-friendly cleanser like pre-paint cleaner. Next, shed the vines and moss sprouting out of the foundation of the wall. Use a pressure washer to hose down remaining roots and dirt. Remove efflorescence i.e. a white powder that emerges on wet concrete by phosphoric acid masonry cleaner.

Remove old paint

Strip down or blister the paint indoors with the help of a wire brush that cost around $3 to $5, a paint scraper ($10-$20) and elbow grease. While removing paint outdoors use a power washer to get rid of the old paint which costs around $40 to $75 on the rent daily.

Seal Interior Concrete

Water and air move through standard concrete. So, sealing concrete is a necessary measure to prevent water vapors to seep in or promoting the growth of mold and the damp basement like feeling. Closing cracked patches through masonry sealer like Thoro seal can cost around $35 for a 50-pound bag.

Carefully follow the complete instructions for mixing, curing and applying the sealer. Masonry sealers usually require two coats. Painting contractors recommend curing for six to seven days before applying the next layer.

Use a Primer

Primers for concrete are called block primers. Block primers fill up the pores and smoothen out the surface. For exterior foundations and walls, use exterior-grade block filler. Primers like Masonry Bonding primer are suitable for indoor concrete surfaces as well as outdoor concrete and cost around $18 per gallon. Primer takes two hours to dry; you should wait for at least 8 hours but not more than a month, to apply paint.

Paint the concrete

Masonry paint also known as elastomeric wall coating or elastomeric paint is an excellent choice for cement painting as it contains binders that expand and contract with the concrete. Paint applied on the exterior of a house can crack and peel on concrete.

Masonry paints cost for $20 per gallon. They can be tinted, and are thicker than exterior paint. Applying it with a masonry brush, texture or high-capacity roller will give you the best results possible. Some masonry paints are thicker than the exterior paint and contain fine particles that can block air sprayers.

In whatever fashion you may apply paint, let it dry for a day between coats. You will probably need two to three coats of paint, so check the weather forecast for a week before you begin.

Learn More

Best Exterior Paint Colors to Make a Small House Seem Bigger

Posted by on Nov 12, 2016 in Uncategorized

There are thousands of exterior colors to choose from, but this does not necessarily mean you are free to pick any color you desire. In the real estate market, the exterior colors or designs one chooses play a critical role. The tiniest changes you make in your home have the ability to change one’s perception and view of the house, as it would stand out from all the neighboring homes. On the other hand, a wrong color completely puts you off the hook.

Exterior Paint Colors to Make a Small House Seem BiggerHow to choose the ideal exterior house color:

In this DIY era, many homeowners take critical design responsibilities on their shoulders. Use your neighbor’s mistakes to your advantage. Smart, well-informed home color decisions helps your home stand out among many, while still availing you with the opportunity to DIY and have fun along the way.

There is an overwhelming number of homes on the market, with many of them accessible at extremely affordable prices. Anything you do to improve or maintain your home’s value is critical. Plan ahead to spare yourself from countless headaches and strains of misfortunes along the way that would demand you part with thousands of dollars, even if you do not intend to sell the house within the next year or two.

For some homeowners, the painting process appears to be a very personal decision. Based on the fact that there are thousands of paint colors to choose from and anything appears to be possible as long as it is appealing. Thus, creating results that you will think back ten years down the line and be grateful for the fact that you did not pick a bad aquamarine color. Thus, this is a choice that would make your neighbors wonder if you hired an expert and continued to envy for years to come.

Step 1: Establish the surrounding elements

When selecting the ideal house color, it is important to accept and respect your home’s surrounding environment. You only have to stand outside your home and take some steps back to view the larger picture.

First, take an open-minded approach look at your home and establish how it fits into the surrounding environment, including your neighborhood.

For households in a suburban environment, they are often built close to one another and thus will need to evaluate and determine the surrounding house colors. If the surrounding homes have subdued or darker colors, a neutral to light palette would make your home stand out from your neighbors. Additionally, lighter colors have cleaner and timeless appearances. Apply the same strategy to homes with elaborate landscaping.

Step 2: Establish the trim, base, and accent colors

To choose the most suitable house color, pay close attention to trim and accent color stains. They have the ability to make or break the perfect paint design.

After making a decision on the base color to use, the rest of your design decisions remain determined by the base color choice. The trim has to be neutral and complimentary to the base. Although it is common that unsuspecting homeowners would choose a contrasting color for the trim, it is a decision one must avoid.

A different color would emphasize on design elements best left unnoticed. Poorly placed windows, garage doors, and unappealing rooflines are often outfitted in trim. A neutral color helps in expanding the surface area of the home, thus allowing the base color to extend to the edges of the house envelope.

Use complementary colors for accents. For instance, an accent color selected well for the shutters can help bring out the architectural design features of a home. The accent colors help to draw much attention to well-designed features. Such areas are quickly noticed and appreciated.

Step 3: Select the right sheen

After choosing the appropriate main body, trim and accent colors, the next phase is to decide on the correct degree of light reflection a paint has. A flat paint reflects little light, whereas high-gloss paint has high-reflectivity releasing a shiny appearance.

The decision on which Sheen to select is also influenced by the condition of the surface in question as well as the durability desired. For instance, larger areas are best used with flat paints. Based on the nature of flat paints, they would be ideal for hiding any surface imperfections occurring on exterior metal or wood surfaces.

Gloss and semi-gloss paints are preferable for application on accents and trims. A higher sheen makes doors and window frames easier to clean. Glossy stains as well tend to provide trim and accents with a professional, finished look.

Conclusion

With all of these features in mind, the trick to selecting the best paint colors is not to only go overboard. Always choose a light base color as this is the key to utilizing the right colors for your house to create a lasting home value and look bigger.

Learn More