An Easy DIY Guide to Painting Textured Walls

Posted by on Jul 15, 2017 in Uncategorized

As a homeowner, you will probably get used to painting textured walls and something you will get to understand and love over time. There is a high likelihood that you make many mistakes over time, but you will soon master the steps. Therefore, below are some tips and tricks for easy DIY textured walls painting:

Painting Textured WallsTip 1

As you shop for painting tools and equipment, select materials based on the walls you work on. For textured walls, puffy roller covers hold more paint and their texture helps in distributing paint across the many recesses of the walls with ease.

Tip 2

Do not use flat finish paint on walls regularly exposed to contact with others as cleaning such walls is next to impossible.

Practice on edging walls freehand without tape to avoid any unnecessary disappointments in the end, while saving time.

Tip 3

Tape textured ceilings only if you have crown molding to avoid disappointments. Many homeowners make this mistake when they DIY textured surfaces for the first time, relax and give the paint time to dry before removing the tape. Such mistakes are terrible, as you would remain with bleeds on the ceiling along the recesses in texture because of the tape not gripping. Alternatively, your paint would peel off the wall because of allowing the paint to dry for long before you remove the tape.

Tip 4

Ensure those baseboards are clean and thus free from dust.  Dirt and dust prevent tape from adhering firmly, which can lead to bleed-through.

Tip 5

For edging on textured walls, a high quality two and a half inch angled brush works best as it can hold more paint. Therefore, this comes in handy for filling all crannies and nooks along wall edges. Feel free to experiment with smaller brushes. They are ideal for reaching hidden and other hard to reach areas.

Tip 6

The Handy Paint Cup is a favorite edging tool beside brush for most homeowners. Its handle hangs comfortably over your hand with the cup holding a reasonable amount of paint. If you need to put down your brush, it has a magnet towards the back border of the cup which is intended for this purpose. It holds your brush over your paint in an upright manner, so it is not submerged into the paint.

Tip 7

As you edge along textured ceilings, make sure to load your brush well. Start from the ceiling and drag the brush gently along the ceiling line. By moving in a slow manner, you give the paint time to creep into all crevices on the ceiling as you move along.

Tip 8

Do not overload your brush with paint when edging baseboards. Start two to three inches above the baseboard and work your way down. By doing this, there would be lesser paint on the paintbrush by the time you reach the baseboard.

Tip 9

Do not saturate your roller with paint when painting ceilings. Apply numerous light coats and roll slowly to reduce on splatter. If you use too much paint, it would probably drop from the roller. To avoid such, paint your ceilings with light, slow layers.

Tip 10

Avoid rolling paint more than twice. However, only do this over areas that have obvious missed spots due to insufficient paint on the roller in the first place. It is, however, likely that if a roller misses certain spots with the first stroke on a textured wall, then you will miss it again.

Tip 11

If you want to take a break, or wait to finish a room the following day, avoid washing the tools and equipment you use but instead wrap them with tight plastic bags.

By adhering to these tips, you would be rescuing yourself from the common mistakes made by many DIY homeowners painting their textured walls for the first time.

Learn More

Things to Consider before Painting Your Walls White

Posted by on Jun 8, 2017 in Uncategorized

Painting the interior house white is an inappropriate way of bringing a fresh start to a home’s interior. A strategy employed by many people immediately after purchasing a home. Some people even prime walls white before they move in.

  1. Natural source of light.

Things to Consider before Painting Your Walls WhiteBefore deciding to paint a house white, it is prudent to consider the natural light source and the orientation. A grey-blue light is typical for rooms facing away from the midday sun, always ideal for a studio, gym or summer bedroom. White paint optimizes the color making things fresh.

The room that does not experience the sunlight is the ideal candidate for color pigments that are warm substituting the absence of the light and as well gives the place the warm vibrant, and the active vibe feels that could have been gotten from the sun. Warm colors stir heat with no doubt hence the warm feeling.

  1. The outside elements affect the inside as well.

A quick glance at the vegetation outside helps one determine whether they play a part in the room’s usage.  The foliage leaves might in a way or the other effect light transmission to the house and thus play a role in the type of color used in painting the interior. The season also plays a part in color contention and as such carefully considered.

After using the color white on the walls and the view is great, painting the trim to match it is a great move in the color decision. A frameless landscape between the walls and woodwork created by using white paint to delineate it.

  1. Reconsider the gallery look.

The reason behind painting the trim and photo on the walls the same bright white color is to bring out and focus the detail in the artwork.

In case a house does not have the art collection, white can be very inappropriate with as it majors in the bright display of the imperfections within the house and the disorder as well. This fact may however not hold water for freewheeling families. That is the reason for taking down a show, galleries paint. The imperfections displayed by the white color creates the impression of khaki pants harboring all sorts of bumps and dirt.

  1. History plays a part.

White is formal, classic, restrained and refined in style. For federal interiors or Greek revival, white is expected in the walls of the third-floor bedrooms and kitchen as well as the trims. Painting everything white is never a white decision.

For you to support your architectural history, there are contextual requirements in the decision to choose on the color contentions. White color on trims says a whole lot of wrong especially when paired with a full colored wall.

  1. Application of white for room expansion.

The white color tends to make a small room appear large based on the light amplification. Edges and shadows also tend to diminish in the white space. It is thus important to keep in mind that the white color is capable of opening and enlarging small rooms.

Navigational human habits and spatial perceptions tend to improve drastically especially when the contrast in color of subsequent rooms is not sharp. An example is a deepening white as the room size increases diminish the difference in size variations.

  1. Texture addition to the white color to do away with the striking look.

The cleanliness of the bathroom or the kitchen not well manifested by any color on the walls other than the white color, especially if kitchen fixtures are also white. Naturally, white is associated with cleanliness and as such while prospects to sell a house are in place, painting it white improves the impression created.

Drawbacks, however, can be realized when a room is whitewashed. A boring, sterile or even a hard surface, formed by reducing the bathroom elements designs to one single color. The addition of a textured surface to the wall saves the day by lowering the pallet creating interests.

  1. The closet and the walls do not have to match.

Lighting in cabinets is usually an afterthought, and most do not have windows. Thus, creating a poorly lit and viewing space for the room while at the same time creates a problem in the process of outfit selection.

For maximum visibility in the closets, a bright white color contention is the best choice for the cabinet interiors.  To ensure the maximum reflective aspect of the white color shades, it advisable to check in the local stores for the color card. The higher the light reflective value of the chosen color tone, the greater the amount of reflected light and as such, the best paint for the closet walls.

Learn More

Simple And Easy Tips and Tricks on Painting Accent Walls

Posted by on May 15, 2017 in Uncategorized

For you to paint your accent walls in a professional manner here are some straightforward tips and tricks to help you go about it the easy way.

Tips and Tricks on Painting Accent WallsFirst step to painting your accent walls

The initial step to painting any wall is to start by selecting an ideal printer’s space. It is crucial to get the correct tape, as many lower cost alternative tapes may not stick well to the walls, thus allowing paint to seep. For long lasting success scores, it is mandatory that you use high-quality, flexible caulking, often ranging at prices between $5 and $7.

With the right kind of caulk, you can eliminate unneeded spaces and gaps between your wall and trim, guaranteeing you a longer lasting tenure. Cover your floors with plastic so as not to damage your flooring. Spare the first few minutes for this step to avoid wasting many hours after you finish.

Application of the right prime

When preparing an accent wall for painting, you can use a primer because it aims at allowing your top layer to dry in a smooth even manner. Many individuals perceive white primer as the best option before applying paint. Always dye your primer a similar color to the paint to use as this works best by allowing you to apply lesser coats of stain as you get the same rich, vibrant color you desired. Similarly, you can utilize a water-based stain blocking primer to cover grease, water stains, scuff marks and ink. If your walls have new drywalls installed, then a Poly Vinyl Acetate (PVA) primer is the best to help seal the surface.

Picking an appropriate color for your accent wall

Selecting the right color for your accent wall is based on the existing colors within your home. Therefore, it is better to invest in a piece that would last longer, rather than something that needs extra cost incurrences down the road. In any case, if you have an existing color palette all over your home, then you will have to use a color from the scheme for it to work.

Matching existing color schemes in a room to accent walls

It is very simple to match your existing color scheme. Select the next darker or lighter color on a color wheel, as they may not match well with your color scheme. It may be a different tone, pigment as well as a different color range. If there exists a particular color in your space you would wish to base your accent wall from, then you need to alter the saturation of that color. You can do this at your local paint retail store.

For instance, your wall color is red, and you want your accent wall to be a lighter red color. Ask for your original red color at 50%, meaning that the store would add the same pigment combination at only 50% of the initially prescribed amount for your color to turn out brighter.

The same applies if you want a darker red but at color 150% bringing about the same color but at a darker density. Such process guarantees your stains will match as they are the same color. Alternatively, choosing your accent wall color does not entirely have to be of similar tones as the other walls in your room.

Bottom line, you do not have to select the same color for your accent walls, but can opt to go for different colors. All this is as long as you ensure to maintain the right shades for matching.

Learn More

Precautions and Procedures to Follow to Ensure Success When Painting Brick

Posted by on Apr 22, 2017 in Uncategorized

Painting is a complicated process. You have to do it right from the first step to the last for you to achieve satisfactory or desired results. There exist numerous reasons as to why homeowners choose to paint or repaint bricks at their homes. For instance,

  • In case one or two bricks at the fireplace are uncoordinated with the décor applied into the room, it is best to repaint than replace the whole block.
  • A layer of bright-color paint has the ability alleviate the feeling of heaviness imparted by the brick wall.
  • If a brick of a home exterior needs some level of a makeover, staining it gives the property a rejuvenated look, boosting its appeal and to some extent resale the value back to its original.
  • Even though any DIY homeowner can paint bricks, there are procedures and precautions to look out for to ensure color success.

Precautions and Procedures to Follow to Ensure Success When Painting Brick

Preparations

Before you begin painting bricks, clean it vigorously so that your paint adheres well during application. Remove efflorescence and dirt with detergent and soapy water, scrubbing with a bristled brush. If this is not satisfactory, and you are thinking of something much stronger, Trisodium Phosphate (TSP) would do the trick by mixing half a cup with one-gallon water. Larger brick spaces are best rinsed with the use of a pressure washer.

When you encounter mildew, apply a mixture of bleach and water in the ratio 3:1, allowed to soak for half an hour then move on to scrubbing the surface with a wire brush. However, do not use acid cleaning solutions, as these may compromise your paint job.

If the brick was recently installed, give it the time of up to a year to dry and acclimate before you paint it. However, if the installation has been in place for years, observe the mortar for any signs of damage. Repair any minor cracks with acrylic seal. For issues more pronounced, repainting the brick would also be ideal. Whether you do any repairs or not, keep in mind that block must be dry completely for the paint to adhere well. After cleaning, take a break of more than 24 hours.

Painting

Based on the surface you wish to paint, use a roller, brush or paint sprayer to apply a layer of latex primer. Add extra coats on those areas affected by either mildew or efflorescence. Regardless of the number of coating layers added, let the primer dry entirely before proceeding any further.

For paint, many prefer using an elastodynamic paint for brick, probably because it features a high level of elasticity, making it perfect for filling and preventing cracks. In addition to this, elastodynamic paint applies well in all weather.

In case you cannot use elastodynamic paint for any particular reason, you can opt to go with regular acrylic latex exterior paint. Acrylic latex is, in fact, the better choice for exterior brickworks because it is made to withstand mildew and quickly evaporate any moisture absorbed.

The simplest way of staining large bricks areas is with a paint sprayer, but if covering only a small area, such as a fireplace, rollers or brushes are sufficient. More so, for those without experience in operating a sprayer, rollers and brushes are recommended for you. If you consider using a roller, choose one that has a thick nap for best results on the brick. For exterior and interior bricks, professionals recommend the use of semi-gloss or gloss paint.

Staining

As long as the brick is in good condition, there are other finishing options to choose.

Staining. Much easier and quicker than painting. Staining highlights the block’s unique texture. Preparing for staining bricks is not in any way different from preparing it for painting. For both cases, clean the surface vigorously and allow it to dry before moving forward. Seal off the mortar with painter’s tape if you do not intend to paint or stain it.

Using the brush that’s accompanied with the staining kit, try the stain on a hidden area of the brick. Lighten or darken the shade by adding water or pigment respectively. Once you attain a mixture that portrays a color you like, move the brush in a uniform manner to spread on the stain. Alternatively, wipe the stain using a clean rag for a more even application. Cover the stain as thinly possible and wait for at least 24 hours before adding the second layer.

Finally, always remember to use protective gear at all times.

Learn More

How to Cover a Dark-Colored Wall with a Lighter Paint Color

Posted by on Mar 4, 2017 in Uncategorized

Covering a dark-colored wall with light color paint is a challenging task. When you spend your time and resources painting a dark-colored wall, you do not want to get upset by seeing the shadows appearing through your fresh paint. With the help of the right painting tools, a primer and paint you can avoid unpleasant surprises when the paint job is complete.

Cover a Dark-Colored Wall with a Lighter Paint ColorClean Walls and the Painting Tools

You should use a mixture of warm water and mild dish detergent to remove dirt and grease accumulated on the wall. Paint sticks fast to clean walls, which makes the surface opaque. The choice of the best painting tools allows you to apply paint and the primer in a quick and efficient manner. High-quality roller covers and paint brushes help you to hide your dark colored walls by releasing color in a smoother and heavier film. A high-quality paintbrush should have split ends to produce an even finish, be comfortable to behold, and has a flexible tip. The bristles should be twice the length of the width of your paintbrush and should not fall off briskly. Squeezing the roller cover determines the quality. If it comes back to original shape after squeezing, then it is of good quality; otherwise, it is of poor quality.

Primer

Applying at least two coats of high-quality primer and sealer can seal the dark-colored walls having tiny interstices through which air may pass. Light-color may produce an uneven tone if the black walls are not sealed; this causes the dark color to show through the paint. Add a proportionate of gray color to your primer or another color which is similar to your primer. The tint reduces the amount of topcoats of paint you will need to apply. The tinted primer also makes your paint opaque covering the blemishes and dark color of the wall surface. Let the primer dry between the coats.

Paint

Using a diluted or low-quality paint reduces the hiding capacity of dark-colored colors. High-quality paints contain a greater amount of pigments and preferred binders than the low-grade paints. These ingredients adhere to the wall after color dries which provides better coverage. Titanium dioxide is a common ingredient of high-grade paints, a pigment which increases the hiding power of color to eliminate any dark colors showing through light colors. Remember to mix the paint thoroughly before applying it.

Dry Time

Allow every coat of primer and topcoat to dry for about 10 to 12 hours before applying the next layer. The insufficient time between primer and color application decreases the hiding power of paint. If the paint is not completely dry before applying another coat of paint, then the paint can fail to hide bold-colored wall underneath it. Time given to dry may vary according to the type of weather but at least two hours between interior latex coats. The humidity level also impacts the time that paint takes to dry.

Hopefully, these tips can help you cover dark-colored walls with a lighter paint color successfully.

Learn More

Decorative Painting 101 – Wall Stencils Technique

Posted by on Feb 19, 2017 in Uncategorized

The wall stencils that heroically got into the market have over time dominated smart and lovely wall decor. They exist in many designs, and it is one’s personal choice to pick whatever plan suits them. The good thing is with just a little practice; even a DIY novice can do the job.

Decorative Painting 101_Wall Stencils TechniqueThe article provides a guideline for using the wall stencils to make an attractive design on the walls. The tools needed include

  • Stencil
  • Stencil brush
  • Paint tape
  • Paper towel
  • Painting container
  • Pencil
  • Spray adhesive
  • Leveler

The manual

A clean, fresh wall with white coats of paint is the starting point. There are two approaches involved, and one is putting the stencil in the middle whereas another is putting it at the corner. Central placement, however, is advisable for symmetry purposes. Application of the spray adhesive on the wall then follows. It ensures right stationing of the stencil. After confirming the location of the stencil, it is adjusted on the wall. The alignment should be beautiful to avoid any flows that may occur.

After proper alignment, use a pencil to mark the stencil alignment on the wall. The direct use of the stencil is not as prudent as employing the utilization of a painters tape. This because the tape does not make the wall dirty and as such no cleaning after that as in the use of pencils of which the pencil marks will need erasing after stencil painting.

After the tape or pencil, painting the stencil begins. The paper towel is then used to shed most paint into it. Next, fill the stencil with paint using the stencil brush. For best results, punching motion is the technique. Because of the extra paint on the towel, fill the brush three to four times for the different areas.

When taking away the Stencil, the adhesive side should always face up. The purpose is the removal of paint that may have stuck beneath the stencil. Clean the wall from side to side using the tip of a brush or using the paper towel. For you to paint corners, a stencil is best for securing a particular side, done by holding one side down using the painters tape.

Some other notable facts include:

For best results, quality stencil brush is a necessity. Stenciling should not directly begin from the wall but instead tried on a large board first, thus reduces the chances of ruining the wall and guarantees a uniform and clean look. It takes the time to do the stenciling job and hence a lot of patience is necessary.

Employing the use of a foam roller to stencil is the fastest easiest and quickest form of stenciling. However, this calls for a decision to have the entire wall stenciled. It may also call for a small section of the wall to stencil.

Using a roller foam

The paint can is properly shaken followed by spraying of the stencil using the spray adhesive. The stencil is then carry put on the wall to start the work. Additionally, to avoid blotting, do not fill the roller with paint. Pressure is needed in the roller use for crisp and neat outcomes. Roll the roller over the stencil carefully.

If you do this right, look out for the results. Should it not turn out as expected, repeatedly move the roller on the stencil using light strokes, the process continues until the results turn out as expected. Analyze the effects simply by lifting the stencil off the corner. It should start at the initial stages of the job based on the ease of making changes at the beginning after which the stencil is put back to continue the job.

In the rolling process, if the roller runs short of paint, refill it with paint and, do not press hard on the stencil to eliminate the excess paint.

When closer to the edge, rolling over the edge is necessary. The paint is then cleaned using baby wipes. Tape can be added to the edges of the stencil to avoid paint reaching on those parts.

Stencil repeatedly until you achieve the desired. An advantage is regular cleaning is inappropriate. Clean the stencil every time you want to apply different color stains.

Learn More